How to Put a Popsocket Back on

How to Fix Popsockets

Rate this post

How to Put a Popsocket Back on

Popsockets are phone grips that may be customised and adhere to the back of your phone. If you have one, you know how much easier it is to use your phone. Popsockets, on the other hand, are tough and can usually be patched back together. The mounting base of your Popsocket has to be cleaned every now and then to keep it sticky. Reassembling a Popsocket is as simple as snapping the remaining components back together if the mounting base is still in place. You won’t have to buy a new one if you maintain it properly.

Replacing a Popsocket Cap

How to Fix Popsockets 2
Locate the slots on the Popsocket funnel’s upper edge.

1. Locate the slots on the Popsocket funnel’s upper edge. The primary component of a Popsocket is a funnel-shaped element that goes above your phone’s adhesive base. Around the rim, there are four little slots. The cap includes four tabs that slip into these slots and keep the cap attached to the funnel.

  • The Popsocket cap is the component of the funnel that fits over the larger aperture. It’s the section with the image on it unless you have a plain Popsocket.
  • If the funnel has come loose, reattach it before replacing the top.
How to Fix Popsockets 4
Snap the cap’s tabs onto the funnel’s open slots.

2. Snap the cap’s tabs onto the funnel’s open slots. Place the cap on top of the funnel and begin inserting the tabs one by one. To push the cap’s tab through the hole, tilt it gently. After you’ve inserted the first one, go on to the next tab and do the same. Then repeat for the remaining tabs to fasten the cap’s opposite end.

Use cautious while putting on a cap. Even if you’re unlikely to break one of the tabs or the funnel, take your time to make sure you don’t have to replace it all.

How to Fix Popsockets 6
To snap the cap in place, press down on it until you hear a pop.

3. To snap the cap in place, press down on it until you hear a pop. Maintain a tight hold on your phone. Keep your hands on the case’s edges to avoid putting strain on the screen. Then, using your thumb or palm, push hard on the cap. Keep your ear out for a loud pop. It’s an indication that your Popsocket is still in one piece and ready to use, as the name implies.

  How to Box Out in Basketball

Because popsocket caps are interchangeable, any cap will fit over the funnel you’re using. You may simply remove the present cap at any moment if you want to test a different design.

Reassembling a Popsocket Funnel

How to Fix Popsockets 8
If the cap is still on the Popsocket, press on the tabs to remove it.

1. If the cap is still on the Popsocket, press on the tabs to remove it. Push on one of the tabs with one hand while holding the funnel. Make sure it comes out of the funnel’s hole. Then, to prevent it from being stuck again, move it away from the funnel. To remove the cap, repeat the process with the remaining tabs.

  • Because a Popsocket cap has four tabs, you’ll have to repeat the process four times to remove it. Because Popsockets are designed to be disassembled, removing the cap will do no harm.
  • To reconnect the funnel, the cap must be entirely removed. Fit the funnel piece back on the base before replacing the cap if yours is already off.
How to Fix Popsockets 10
Place the funnel on top of your phone’s adhesive pad.

2. Place the funnel on top of your phone’s adhesive pad. The pad features a hole in the middle and serves as a basis for the remainder of the Popsocket. Turn the funnel over so that the smaller end is facing down. After that, insert it into the hole. It won’t lock in place straight immediately, so keep it in place for the time being.

The pad is required to keep the Popsocket connected to your phone and must be placed initially. If it has come off, clean it before reattaching it.

How to Fix Popsockets 12
To lock the Popsocket funnel in place, turn it clockwise.

3. To lock the Popsocket funnel in place, turn it clockwise. Hold the funnel vertically above the base to keep it centred. To keep it fixed in place, press down on the middle with your thumb. Then, using your free hand, start twisting it. It will click into place after roughly a quarter-turn.

  • Pull the funnel away from the base of the Popsocket to test it. You won’t be able to move it without tugging it off your phone if it has clamped onto the base.
  • It makes no difference either direction you turn the Popsocket. It will still lock in place if you rotate it counterclockwise.
How to Fix Popsockets 14
Fit the cap’s tabs into the funnel’s holes to complete the installation.

4. Fit the cap’s tabs into the funnel’s holes to complete the installation. Around the upper edge of the funnel are four little apertures. When you gaze straight down into the funnel, you can see them. Slide the tabs into the holes one at a time to reinstall the cap. Once you’ve got the first tab in, the rest is a piece of cake.

  • Lift the cover off the funnel once it has been connected. You won’t be able to move it if all of the tabs are in the holes. If you can lift any section of the cap, locate the loose tap and tighten it to prevent the cap from falling off.
  • Because all Popsocket caps have the same structure, you may simply modify yours by swapping out the cap. It’s as simple as removing the old cap and replacing it with a new one.
  How to Fold Gauze for Your Mouth

Securing a Loose Popsocket Base

How to Fix Popsockets 16
To clean the Popsocket, run warm water from a sink faucet.

1. To clean the Popsocket, run warm water from a sink faucet. Allow the water to flow for a few moments before checking the temperature. Make sure it’s warm but not too hot. Popsockets are simple to clean, however cold water is more effective, and hot water may damage the material.

Fill a glass or dish halfway with water and use it to wash the Popsocket. It is, however, simpler to clean under flowing water.

How to Fix Popsockets 18
To moisten the Popsocket base, dip it into the water.

2. To moisten the Popsocket base, dip it into the water. Place it in the water with the adhesive side down. If your Popsocket is in one piece, you may submerge it completely in the water for a few seconds. The substance will not be harmed. If it doesn’t work, make sure the adhesive foundation is moist so you can scrape it clean.

Popsockets may be safely soaked in water, although it is not necessary. It’s best to clean it gently so that it doesn’t take as long to dry.

How to Fix Popsockets 20
To clean the Popsocket’s sticky base, rub it with your fingers.

3. To clean the Popsocket’s sticky base, rub it with your fingers. Dip your thumb in the water and move it around the base in a circle. To get rid of the majority of the debris, do this for 30 to 60 seconds. Then, feel the bottom part of the base for any remaining debris. Continue massaging it until the base is clean, wetting the Popsocket and your finger.

  • If you remove a Popsocket from your phone, it is almost certain to get filthy. Fortunately, after you get the debris out of the way, it generally sticks back on.
  • Clean off the rest of the Popsocket as you’re cleaning the base. Remove the cap and rinse off the funnel’s inside.
How to Fix Popsockets 22
Allow 10 minutes for the Popsocket to air dry on a towel.

4. Allow 10 minutes for the Popsocket to air dry on a towel. Find a location in your room that is open but not in direct sunlight. Place a clean towel on the table and shake the Popsocket to remove as much water as possible. Place it on the towel and wait for it to dry.

  • To avoid drying out, the manufacturer suggests reattaching the base within 15 minutes. Some individuals let the base to dry for extended periods of time without issue, however this may prevent the Popsocket from adhering to your phone.
  • If you place the adhesive side of the Popsocket on your towel, it will be difficult to remove the Popsocket!
How to Fix Popsockets 24
To connect the Popsocket to your phone, replace the base on your phone.

5. To connect the Popsocket to your phone, replace the base on your phone. Make sure the back of your phone is facing up. Then firmly push the base’s adhesive side against it. Place the funnel in the little hole on the base and lock it in place with a quarter-turn clockwise. To complete reassembling your Popsocket, insert the cap on top and slide the tabs into the little holes on the funnel.

  • To guarantee that the Popsocket sticks, plan on leaving your phone with it for roughly an hour.
  • Pick up the Popsocket after an hour and give it a thorough examination. It should remain connected to your phone at all times. If cleaning it does not work, you may need to get a new one.
  • Remove any goo from the base of your phone by wiping it with a cloth soaked in rubbing alcohol.
  How to Take an Inch off Your Waist

Similar Posts