How to Sew a Patch on a Uniform

Rate this post

Many individuals wear uniforms with patches, whether for the military, public service, scout unit, or other reasons. When you are promoted or receive a new badge, you may need to sew a new patch onto your uniform. Sewing patches on a uniform is a basic, easy technique that may be done by hand or machine.

You are viewing article How to Sew a Patch on a Uniform at website answerforyou.net.

Hand Sewing a Patch

1. Before you begin, wash, dry, and iron your outfit. If it’s a new uniform, wash and dry it before sewing on the patch, otherwise the cloth may bunch unevenly beneath the patch after the first wash and dry cycle.

  • Cotton is used to make several uniforms. Cotton often shrinks somewhat after the first wash. If you sew a patch onto your uniform before washing it, the cloth behind the patch will shrink and pull, bunching it.
  • It is also a good idea to iron the patch placement area before beginning to sew. Any creases will be removed by ironing the area. If you sew your patch over creases, your uniform will be wrinkled indefinitely.

2. Take out your sewing needle and thread. Choose a thread that matches the color of the uniform or the border of the patch.

  • If you can’t locate the same color thread as either, try for a darker color that’s as near as possible.
  • Darker thread, rather than lighter thread, will mix better and not stand out as much. You may also purchase a transparent thread to cover it up.

3. Place the patch in the proper location. Some patches, such as those seen on military uniforms, must be applied in a specified location.

  • For example, if you need to sew on an American flag patch, you should do it in the sleeve’s shoulder/bicep region. The flag must also be positioned such that it faces the correct direction. The American flag should always be positioned such that as the wearer moves forward, the flag seems to be blowing in the breeze.
  • Check with your boss to ensure you’re putting fixes in the right areas.

4. Wear the uniform with the patch secured with a safety pin. This is to ensure that it is properly positioned. It might be beneficial to have someone else confirm this for you.

  • When wearing your uniform with pins holding the patch, be cautious. Put on the uniform carefully so that the pins don’t poke you.
  • The reason you should examine the fit is because as you wear your uniform, your body will fill up the garment. This may have an impact on how the patch appears.

5. Keep your patch in place while stitching. To secure the patch, use a safety pin or straight pin. Alternatively, iron the patch on using sticky fabric tape.

  • Even if you don’t have an iron-on patch, you can consider purchasing some sticky ironing tape. Adhesive tape is frequently preferable to pins since it holds the patch in place as you sew. There will be no need to sew around pins or poke yourself.
  • Cut and apply the tape. Iron the patch on to the tape.
  • You’ll have to pin the patch in place if you don’t iron it.

6. Make a thread spool. If you’re new to sewing, you may want to start with a length of thread no more than 18 inches long (45cm). Longer pieces tend to tangle and are more difficult to deal with than shorter ones.

  • You might also try not cutting the thread and leaving it on the spool. This will also assist to keep the thread from becoming knotted.
  • Furthermore, you won’t have to worry about running out of thread and having to re-thread your needle.
  How to Make a Cutoff Shirt

7. Thread the needle and knot the thread at the end. Threading the needle may be challenging. Make use of a needle threading tool to save time.
If you don’t have a threading tool, twisting and wetting the thread in your tongue may assist. The saliva will act as a temporary glue, holding the microscopic thread strands together. This makes it easier to thread the needle’s eye.

8. Thread the needle through the cloth and the patch. Begin by poking the needle through the patch on the inside of your clothing.

  • Begin on the inside of your cloth so that the knot you make to secure the thread in place doesn’t show on the outside. Begin by poking the needle inside.
  • If the patch is round, use an overcast stitch as a guide while sewing it. This will allow you to stitch it more precisely.

9. Use a straight stitch pattern to sew. Return the needle approximately 1/4 of the way through the uniform “(6mm) from the point where you took it out.

  • A straight stitch is not only the simplest but also the fastest technique to sew patches on. You don’t need a fancy stitching design, particularly if your patch was pressed on.
  • Straight stitches are also the least noticeable.

10. Continue to sew the patch. Continue your straight stitch around your patch until you’ve finished it. You should finish where you began.
When hand sewing a patch onto a uniform, it’s crucial to take your time and do your best to ensure that your weaves and thread lengths are as equal as possible. Maintaining an even pattern helps improve the appearance of your patch.

11. Tie your thread. When you’ve finished sewing all the way around the patch’s edge, loop the thread and draw the needle through to tie off your knot.
To finish sewing your patch, thread your needle through a little loop on the inside of your uniform. Thread the needle through the loop and tighten the thread. This will result in a tight knot.

12. Cut the thread at the ends. Remove any loose threads that are dangling beyond the knot.
You should leave around 1/2 inch of thread “(1cm) long. Leaving a little amount ensures that the knots are not mistakenly snipped. tuck the thread under the patch

Machine Sewing a Patch

1. Iron your clothing. You should press your uniform before stitching to smooth out any creases.
Ironing your item before sewing keeps you from sewing over wrinkles and creating permanent creases in your garments.

2. Place and place the patch as desired. Before sewing, it’s a good idea to position your patch on your clothing or uniform and make sure it’s in the right area.
If you sew your patch onto your uniform and then discover you placed it in the incorrect location, you must remove the patch and start again.

3. Iron your patch on. Even if you don’t have an iron-on patch, you can consider purchasing some sticky ironing tape. Cut and position the tape. Iron the patch on to the tape.
You’ll have to pin the patch in place if you don’t iron it. When you use your computer, pinning your patch will increase the amount of work you have to do.

  How to Track a Package Without a Tracking Number

4. Position the garment on the sewing machine. Set up your machine so that the needle length for the patch is shorter. Set the sewing machine to straight stitch. Put your presser foot in the up position. Each sewing machine will have unique characteristics and capabilities. It is important to consult your handbook for the best results.
Make certain that the patch is only sewn onto one piece of cloth. It might be difficult to sew your patch onto a sleeve. To avoid sewing your sleeve shut, pull back the opposite side of the sleeve without the patch.

5. Thread your sewing machine. Thread the bobbin with the thread. Your handbook will have instructions on how to accomplish this appropriately. In general, thread your thread through the bobbin on the spindle. Wind the thread around the bobbin using the spindle. To fill the bobbin, press the foot pedal. Once the bobbin is full, you must put it in the appropriate area on your machine. Then, to join the thread to the needle, pass it through the appropriate sections of the machine. This is done differently on each computer. Consult your handbook.
Check that you’re using the right color thread. You should use either the patch’s color thread or clear thread.

6. At begin, set the machine to a low speed.
Your sewing machine will very certainly have many speed options. The speed determines how fast the needle travels. You’ll want to keep it low so you can stitch with excellent control.

7. Begin stitching. To engage the needle, press down on your foot pedal and gently move your clothing until you’ve finished stitching the patch. Move both the clothing and the patch as one. Check that the sewing machine’s foot is up and the needle is in position.

  • When you need to rotate, raise your foot up so you can move the clothing. However, maintain the needle in position to ensure a uniform pattern.
  • Seal the stitch after you’ve gone all the way around your patch.
  • Cut any loose threads with your scissors. You should leave around 1/2″ (1cm) of thread hanging. Leaving a little amount ensures that the knots are not mistakenly snipped.

Sewing a Patch on a Sleeve

1. Using a seam ripper, remove any patches that need to be replaced. If you need to change a patch because you’ve been promoted, first use a seam ripper to remove the thread. The patch should then be removed.

  • Thread every stitch around your patch.
  • Using the tweezer end of your seam ripper, remove any loose thread.
  • If you use a razor, you risk cutting yourself or your clothing.

2. Iron your clothing. You must iron your sleeve or clothing to remove any creases.

  • Ironing may also assist to smooth out any remaining blemishes and punctures from prior patches.
  • Ironing your item before sewing prevents you from sewing over wrinkles and creating permanent creases in your garments.

3. Place the patch in the proper location. Before sewing or gluing the patch on the sleeve, double-check its placement. If you are sewing a patch on a military uniform, you will be given explicit instructions on where to sew the patch.

  • A Navy striped patch, for example, must extend 2 inches (51 mm) over the sleeve cuff. To properly place patches, refer to any instructions you were provided.
  • You may either pin the patch on or iron it in place using adhesive tape.
  • Ironing the patch on is not a long-term solution. It merely serves to keep the patch in place as you stitch. Because there are no pins, you can sew the patch on without hitting any.
  • Allow the patch to cool before sewing if you ironed it on.
  How to Fix an Xbox 360 Wireless Controller That Keeps Shutting Off

4. Attach your patch on your uniform. This may be done with either a sewing machine or by hand stitching. Use the appropriate color thread. Use clear thread or match the color of the patch’s edges.
If you’re using a machine, be sure you pull the sleeve back that isn’t tied to your patch.

5. Slow down. Take your time so you get it correctly the first time and don’t have to start again.

  • Sewing may be more challenging depending on where your patch is located. If the patch is higher on the arm, you may separate the layers of cloth with your neck opening. If it’s lower, towards the cuff, you’ll have to be careful not to stitch through both sides of the sleeves.
  • Set your machine at a slow speed. If you need to rotate your uniform and patch, lift the foot while keeping the needle in place. Rotate your clothes before lowering your foot.
  • Take your time while hand stitching so that you may leave equal spacing between each pass and sew in a straight line. On patches, use a straight stitch.

6. Tie a knot or use the sewing machine to secure your thread. When you’ve finished stitching all the way around the patch, tie a hand knot or backtrack on the machine.
Cut any loose threads with your scissors. You should leave approximately a 1/2″ (1cm) long thread. Leaving a little amount ensures that the knots are not mistakenly snipped.

How do you sew patches on army uniform?

Method 1: Machine Sewing
Step 1: Iron your uniform to eliminate any creases and wrinkles.
Step 2: Take your patch and arrange it correctly on your jersey. …
Step 3: Use ironing tape or a garment pin to temporarily attach the patch. …
Step 4: Prepare the sewing machine for operation.

What stitch is best for patches?

Use a basic backstitch to bind the repair and produce a tidy, uninterrupted line using this approach. Keep your stitches about 18 inch from the edge of the patch—this will assist keep the patch flat on the cloth.

How do I put patches on military?

The American flag should be placed over the unit patch on your right shoulder. Your name tape should be placed slightly above your ACU’s right breast pocket, and your branch tape should be placed above the left breast pocket. Attach your enlisted rank patch on the outside half of each sleeve, between the shoulder and the elbow, for your ASU.

Is it better to sew or iron on a patch?

Sew-on patches are also a good option. They increase the versatility of the clothing to which the patch is affixed. So, if you don’t want your patch to be rigid, you may remove the iron-on backing and, once stitched on, the patch can flow a little with the cloth.

How do you apply a patch without an iron?

If you don’t have an iron, a hair straightener can do in a hurry! Make a design plan. Put your item of clothing on the ironing board and place the patch in the desired location. The adhesive side (the side that does not include the pattern) should be flat on the cloth.

Similar Posts